MUR180E, MUR1100E
http://onsemi.com
4
MERCURY
SWITCH
VD
ID
DUT
40 mH COIL
+VDD
IL
S1
BVDUT
IL
ID
VDD
t0
t1
t2
t
Figure 6. Test Circuit
Figure 7. Current?Voltage Waveforms
The unclamped inductive switching circuit shown in
Figure 6 was used to demonstrate the controlled avalanche
capability of the new “E’’ series Ultrafast rectifiers. A
mercury switch was used instead of an electronic switch to
simulate a noisy environment when the switch was being
opened.
When S1
is closed at t
0
the current in the inductor I
L
ramps
up linearly; and energy is stored in the coil. At t1
the switch
is opened and the voltage across the diode under test begins
to rise rapidly, due to di/dt effects, when this induced voltage
reaches the breakdown voltage of the diode, it is clamped at
BVDUT
and the diode begins to conduct the full load current
which now starts to decay linearly through the diode, and
goes to zero at t2.
By solving the loop equation at the point in time when S1
is opened; and calculating the energy that is transferred to
the diode it can be shown that the total energy transferred is
equal to the energy stored in the inductor plus a finite amount
of energy from the VDD
power supply while the diode is in
breakdown (from t1
to t
2) minus any losses due to finite
component resistances. Assuming the component resistive
elements are small Equation (1) approximates the total
energy transferred to the diode. It can be seen from this
equation that if the VDD
voltage is low compared to the
breakdown voltage of the device, the amount of energy
contributed by the supply during breakdown is small and the
total energy can be assumed to be nearly equal to the energy
stored in the coil during the time when S1
was closed,
Equation (2).
The oscilloscope picture in Figure 8, shows the
information obtained for the MUR8100E (similar die
construction as the MUR1100E Series) in this test circuit
conducting a peak current of one ampere at a breakdown
voltage of 1300 V, and using Equation (2) the energy
absorbed by the MUR8100E is approximately 20 mjoules.
Although it is not recommended to design for this
condition, the new “E’’ series provides added protection
against those unforeseen transient viruses that can produce
unexplained random failures in unfriendly environments.
BV
WAVAL
1
2LI
2
LPK
DUT
BVDUT–V
DD
WAVAL
1
2LI
2
LPK
Figure 8. Current?Voltage Waveforms
CHANNEL 2:
IL
0.5 AMPS/DIV.
CHANNEL 1:
VDUT
500 VOLTS/DIV.
TIME BASE:
20 s/DIV.
EQUATION (1):
EQUATION (2):
CH1 CH2 REF REF
CH1
CH2
1 217:33 HRSACQUISITIONS
SAVEREF SOURCE
STACK
A
20s
953 V VERT
500V
50mV
相关PDF资料
MUR120-T DIODE SUPERFAST GPP 1A 200V DO41
MUR130RLG DIODE ULTRA FAST 1A 300V DO-41
MUR140-T DIODE SUPERFAST GPP 1A 400V DO41
MUR2020R DIODE ULT FAST 20A 200V TO-220AC
MUR2100ERL DIODE ULTRA FAST 2A 1KV DO-41
MUR210RLG DIODE ULTRA FAST 2A 100V DO-41
MUR220RL DIODE ULTRA FAST 2A 200V DO-41
MUR240RLG DIODE ULTRA FAST 2A 400V DO-41
相关代理商/技术参数
MUR1100-LFR 制造商:FRONTIER 制造商全称:Frontier Electronics. 功能描述:1A ULTRA FAST EFFICIENT RECTIFIER
MUR1100PT 制造商:CHENMKO 制造商全称:Chenmko Enterprise Co. Ltd. 功能描述:HIGH EFFICIENCY RECTIFIER
MUR1100S 制造商:GULFSEMI 制造商全称:Gulf Semiconductor 功能描述:ULTRAFAST EFFICIENT PLASTIC SILICON RECTIFIER Voltage: 50 to 1000V Current: 1.0A
MUR1100-TP 功能描述:DIODE SUPER FAST 1A 1000V DO-41 RoHS:是 类别:分离式半导体产品 >> 单二极管/整流器 系列:- 标准包装:100 系列:- 二极管类型:标准 电压 - (Vr)(最大):50V 电流 - 平均整流 (Io):6A 电压 - 在 If 时为正向 (Vf)(最大):1.4V @ 6A 速度:快速恢复 = 200mA(Io) 反向恢复时间(trr):300ns 电流 - 在 Vr 时反向漏电:15µA @ 50V 电容@ Vr, F:- 安装类型:底座,接线柱安装 封装/外壳:DO-203AA,DO-4,接线柱 供应商设备封装:DO-203AA 包装:散装 其它名称:*1N3879
MUR110G 功能描述:整流器 100V 1A UltraFast RoHS:否 制造商:Vishay Semiconductors 产品:Standard Recovery Rectifiers 配置: 反向电压:100 V 正向电压下降: 恢复时间:1.2 us 正向连续电流:2 A 最大浪涌电流:35 A 反向电流 IR:5 uA 安装风格:SMD/SMT 封装 / 箱体:DO-221AC 封装:Reel
MUR110GP 制造商:CHENYI 制造商全称:Shanghai Lunsure Electronic Tech 功能描述:1.0Amp glass passivated super fast recovery rectifier 50to600 volts
MUR110GP-TP 制造商:Micro Commercial Components (MCC) 功能描述:Diode Switching 100V 1A 2-Pin DO-41 T/R
MUR110-LFR 制造商:FRONTIER 制造商全称:Frontier Electronics. 功能描述:1A ULTRA FAST EFFICIENT RECTIFIER